ASTM A320/A320M-17a

standard by ASTM International, 05/01/2017
Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service
Category: ASTM

~~$58.00~~ $29.00

Description

Full Description

1.1 This specification2 covers alloy steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for low-temperature service. See Specification A962/A962M for the definition of bolting. The bars shall be hot-wrought and may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strain-hardened. When strain hardened austenitic stainless steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood.

1.2 Several grades are covered, including both ferritic and austenitic steels designated L7, B8, etc. Selection will depend on design, service conditions, mechanical properties, and low-temperature characteristics. The mechanical requirements of Table 1 indicate the diameters for which the minimum mechanical properties apply to the various grades and classes, and Table 2 stipulates the requirements for Charpy impact energy absorption. The manufacturer should determine that the material can conform to these requirements before parts are manufactured. For example, when Grade L43 is specified to meet the Table 2 impact energy values at −150 °F [−101 °C], additional restrictions (such as procuring a steel with lower P and S contents than might normally be supplied) in the chemical composition for AISI 4340 are likely to be required.

Note 1: The committee formulating this specification has included several grades of material that have been rather extensively used for the present purpose. Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent. Users should note that hardenability of some of the grades mentioned may restrict the maximum size at which the required mechanical properties are obtainable.

(A) These upper diameter limits were established on the basis that these were the largest sizes commonly available that consistently met specification property limits. They are not intended as absolute limits beyond which bolting materials could no longer be certified to the specification.

(B) To meet the tensile requirements, the Brinell hardness shall not be less than 200 HBW or 93 HRB.

(C) Class 1 products are made from solution-treated material. Class 1A products are solution treated in the finished condition for corrosion resistance; heat treatment is critical for enhancing this physical property and meeting the mechanical property requirements. Class 2 products are made from solution-treated material that has been strain hardened. Austenitic steels in the strain-hardened condition may not show uniform properties throughout the cross section, particularly in sizes over ³/₄ in. [20 mm] in diameter.

(D) For sizes ³/₄ in. [20 mm] in diameter and smaller, a maximum hardness of 241 HBW (100 HRB) is permitted.

(A) See 6.2.1.1 for permitted exemptions.

1.3 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M.

1.4 Nuts for use with bolting are covered in Section 10 and the nut material shall be impact tested.

1.5 Supplementary Requirements are provided for use at the option of the purchaser. The supplem

Product Details

Published:: 05/01/2017
Number of Pages:: 8
File Size:: 1 file , 110 KB
Redline File Size:: 2 files , 200 KB
Note:: This product is unavailable in Russia, Ukraine, Belarus

Document History

ASTM A320/A320M-17a

Full Description

Product Details

ASTM A320/A320M-22a

ASTM A320/A320M-22

ASTM A320/A320M-18

ASTM A320/A320M-17a

ASTM A320/A320M-17

ASTM A320/A320M-15a

ASTM A320/A320M-14

ASTM A320/A320M-11a

ASTM A320/A320M-11

ASTM A320/A320M-10a

ASTM A320/A320M-10

ASTM A320/A320M-08

ASTM A320/A320M-07a

ASTM A320/A320M-07

ASTM A320/A320M-05a

ASTM A320/A320M-05

ASTM A320/A320M-00b

ASTM A320/A320M-03

ASTM A320/A320M-02

ASTM A320/A320M-01

ASTM D3518/D3518M-13

ASTM D6301-13

ASTM C1403-13

ASTM D7359-13