ASTM B848/B848M-21
- standard by ASTM International, 09/01/2021
- Standard Specification for Powder Forged (PF) Ferrous Materials
- Category: ASTM
$52.00
$26.00
Full Description
1.1''This specification covers powder forged ferrous materials fabricated by hot densification of atomized prealloyed or iron powders and intended for use as structural parts.
1.2''This specification covers powder forged parts made from the following materials:
1.2.1''Compositions:''
1.2.1.1''PF-10XX Carbon Steel (produced from atomized iron powder and graphite powder),
1.2.1.2''PF-10CXX Copper-Carbon Steel (produced from atomized iron powder, copper and graphite powders),
1.2.1.3''PF-11XX Carbon Steel with manganese sulfide for enhanced machinability (produced from atomized iron powder, manganese sulfide, and graphite powders),
1.2.1.4''PF-11CXX, PF-1130CXX, and PF-1135CXX Copper-Carbon Steels with manganese sulfide for enhanced machinability (produced from atomized iron powder, copper, manganese sulfide, and graphite powders),
1.2.1.5''PF-42XX Nickel-Molybdenum Steel (produced from prealloyed atomized iron-nickel-molybdenum powder and graphite powder),
1.2.1.6''PF-46XX Nickel-Molybdenum Steel (produced from prealloyed atomized iron-nickel-molybdenum powder and graphite powder),
1.2.1.7''PF-44XX Molybdenum Steel (produced from prealloyed atomized iron-molybdenum powder and graphite powder), and
1.2.1.8''PF-49XX Molybdenum Steel (produced from prealloyed atomized iron-molybdenum powder and graphite powder).
Note 1:''Alloy composition designations are modifications of the AISI-SAE nomenclature. For example: 10CXX designates a plain carbon steel containing copper and XX amount of carbon. Compositional limits of alloy and impurity elements may be different from the AISI-SAE limits. Chemical composition limits are specified in Section 6.
Note 2:''XX designates the forged carbon content, in hundredths of a percent, that is specified by the purchaser for the application. For a given specified carbon content, the permissible limits shall be as specified in 6.2.
Note 3:''The old acronym for powder forging P/F has been replaced by PF throughout the document. The change in the prefix for the material designations is just to match the currently approved acronym for powder forging. No change has been made to the material specification and performance characteristics for the various powder forged materials.
1.2.2''Grades:''
1.2.2.1''Grade A'''Density equivalent to a maximum of 0.5'''% porosity. The minimum density of those sections of the powder forged part so designated by the applicable part drawing shall not be less than the value specified in Table 1.
1.2.2.2''Grade B'''Density equivalent to a maximum of 1.5'''% porosity. The minimum density of those sections of the powder forged part so designated by the applicable part drawing shall not be less than the value specified in Table 1.
1.3''Units'''The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conf
Product Details
- Published:
- 09/01/2021
- Number of Pages:
- 10
- File Size:
- 1 file , 230 KB
- Redline File Size:
- 2 files , 470 KB
- Note:
- This product is unavailable in Russia, Ukraine, Belarus
Document History
ASTM B848/B848M-21
ASTM B848-15
ASTM B848-10
ASTM B848-01
ASTM C913-08
Standard Specification for Precast Concrete Water and Wastewater Structures..
$30.00 $60.00
ASTM C507-08
Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe..
$30.00 $60.00
ASTM D5453-08
Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine ..
$30.00 $60.00
ASTM C231-08
Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method..
$30.00 $60.00