• ASTM C150/C150M-22

ASTM C150/C150M-22

  • standard by ASTM International, 07/01/2022
  • Standard Specification for Portland Cement
  • Category: ASTM

$54.00 $27.00

Full Description

1.1''This specification covers ten types of portland cement, as follows (see Note 2):

1.1.1''Type I'''For general use, when the special properties specified for any other type are not required.

1.1.2''Type IA'''Air-entraining cement for the same uses as Type I, where air-entrainment is desired.

1.1.3''Type II'''For general use, more especially when moderate sulfate resistance is desired.

1.1.4''Type IIA'''Air-entraining cement for the same uses as Type II, where air-entrainment is desired.

1.1.5''Type II(MH)'''For general use, more especially when moderate heat of hydration and moderate sulfate resistance are desired.

1.1.6''Type II(MH)A'''Air-entraining cement for the same uses as Type II(MH), where air-entrainment is desired.

1.1.7''Type III'''For use when high early strength is desired.

1.1.8''Type IIIA'''Air-entraining cement for the same use as Type III, where air-entrainment is desired.

1.1.9''Type IV'''For use when a low heat of hydration is desired.

1.1.10''Type V'''For use when high sulfate resistance is desired.

Note 1:''Some cements are designated with a combined type classification, such as Type I/II, indicating that the cement meets the requirements of the indicated types and is being offered as suitable for use when either type is desired.

Note 2:''Cement conforming to the requirements for all types are not carried in stock in some areas. In advance of specifying the use of cement other than Type I, determine whether the proposed type of cement is or can be made available.

1.2''The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice.

1.3''The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.4''This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Product Details

Published:
07/01/2022
Number of Pages:
9
File Size:
1 file , 130 KB
Note:
This product is unavailable in Russia, Ukraine, Belarus

Document History

ASTM C150/C150M-22

ASTM C150/C150M-21

ASTM C150-81

ASTM C150/C150M-20

ASTM C150/C150M-19a

ASTM C150/C150M-18

ASTM C150/C150M-17

ASTM C150/C150M-16

ASTM C150-94b

ASTM C150/C150M-12

ASTM C150/C150M-11

ASTM C150-02

ASTM C150-07

ASTM C150-05

ASTM C150-04ae1

ASTM C150-04a

ASTM C150-02ae1

ASTM C150-02a

ASTM D7024-04

ASTM D7024-04

Standard Test Method for Steady State and Dynamic Thermal Performance of Textile Materials (Withdraw..

$25.00 $50.00

ASTM F1977-04

ASTM F1977-04

Standard Test Method for Determining Initial, Fractional, Filtration Efficiency of a Vacuum Cleaner ..

$33.00 $65.00

ASTM A511-04

ASTM A511-04

Standard Specification for Seamless Stainless Steel Mechanical Tubing..

$30.00 $60.00

ASTM D2028-97(2004)

ASTM D2028-97(2004)

Standard Specification for Cutback Asphalt (Rapid-Curing Type)..

$26.00 $52.00